Connect with us

Networking

BGP Explained: The Routing System That Holds the Internet Together

The Border Gateway Protocol is how the internet’s independent networks tell each other which addresses they can reach. Here is how it works and why it occasionally breaks.

Published

on

Telephone pole with many wires against sky

The internet is a federation of tens of thousands of separately run networks. For data to cross from one to another, each network needs to know which neighbors can reach which destinations. The system that shares that information is the Border Gateway Protocol, or BGP.

Networks as autonomous systems

In BGP terms, each independently managed network is an autonomous system, identified by a number. An internet provider, a cloud company, a university or a large enterprise may each operate one or more. Each autonomous system controls blocks of IP addresses.

BGP was first specified in 1989 and has been revised since; the version in wide use today has been the internet’s interdomain routing protocol for decades.

Advertisement

How BGP works

Routers at the edges of each network establish BGP sessions with routers in neighboring networks. Over those sessions, they announce the address blocks they can reach, along with information about the path, including the list of autonomous systems the route passes through.

Each network collects these announcements from all its neighbors and picks the best route to each destination. Best is defined by the network’s own policy, not just by shortest distance. A network might prefer routes through a peer over routes it must pay transit for, or prefer one provider for business reasons.

Once a network picks its routes, it passes some of them on to its own neighbors, and so information spreads across the internet.

Policy is the point

BGP is often called a policy protocol. It lets each network express business relationships: share customer routes with everyone, share peer routes only with customers, and so on. That flexibility is what allows a commercial internet made of competing companies to function as one network.

When BGP goes wrong

BGP was built on a lot of trust. By default, a network can announce almost any route, and neighbors may believe it. That has led to well-known problems:

Advertisement
  • Route leaks, where a network accidentally passes on routes it should not, pulling traffic through an unintended path.
  • Route hijacks, where a network announces addresses it does not own, whether by mistake or on purpose.
  • Self-inflicted outages, where a company’s configuration error withdraws its own routes, making its services unreachable.

Defenses have improved. Resource Public Key Infrastructure, known as RPKI, lets address holders publish cryptographically signed records of which networks may announce their addresses, and many networks now reject routes that fail those checks. Careful filtering between neighbors helps too.

BGP inside data centers

BGP is not only for the public internet. Many large data center networks use BGP internally to route between racks in spine-leaf fabrics, because it is robust, well understood and handles huge numbers of devices. Cloud providers use it to connect customer networks and to announce their services to the world.

For anyone following AI infrastructure, BGP is part of the invisible plumbing that gets requests from users to data centers and lets operators shift traffic quickly when something fails.

A Simple Picture of Route Selection

An example helps make BGP’s policy-driven choices concrete. Picture a regional internet provider that wants to reach an address block belonging to a cloud company. It hears about that block from three neighbors:

  • A large transit provider it pays to carry traffic, with a path passing through two other networks.
  • A peer network it exchanges traffic with at no charge, with a path passing through three networks.
  • A direct connection to the cloud company itself.

The direct connection is usually the first choice. If it fails, many providers would rather use the peer than pay for transit, even though the peer’s path is longer. Shortest path is only one factor; the provider’s own rules come first. When the direct link comes back, BGP announcements update, and traffic shifts back.

This is why traffic between two places on the internet does not always follow the geographically obvious route. Business relationships shape the map as much as distance does.

What Network Operators Actually Do Day to Day

Running BGP well is a craft. The work that keeps it healthy rarely makes news:

  1. Filtering what neighbors can announce. Operators maintain lists of the address blocks each customer is allowed to send, so a mistake on the customer’s side does not spread.
  2. Limiting how many routes a session can carry. A maximum-prefix setting shuts down a session that suddenly sends far more routes than expected, a common sign of a leak.
  3. Publishing and checking RPKI records. Address holders sign records saying which networks may originate their routes, and receiving networks check incoming announcements against them.
  4. Watching from the outside. Public route-monitoring services let operators see how their addresses look to the rest of the world and spot unexpected announcements quickly.
  5. Making changes carefully. Because a BGP error can withdraw a company’s presence from the internet, changes are often staged, reviewed and scheduled.

How to Read a BGP Story in the News

When a large service becomes unreachable and coverage mentions BGP, a few questions help sort out what happened:

  • Was it a withdrawal, where a network stopped announcing its own routes, or an announcement by someone else that pulled traffic away?
  • Was it accidental or deliberate? Most incidents turn out to be configuration errors.
  • Did the affected company’s own systems depend on the same network paths it lost? Some outages last longer because the tools needed to fix them were also unreachable.
  • Did RPKI or filtering limit the damage? Coverage that mentions these defenses gives a sense of how the ecosystem is maturing.

Questions Readers Ask

Why not replace BGP with something more secure?

Replacing a protocol used by tens of thousands of independent networks would require nearly all of them to change at once. Adding protections like RPKI on top has proven more practical.

Can an individual see BGP routes?

Yes, in a sense. Public looking-glass tools and route-data projects let anyone view how address blocks are being announced across the internet.

Does BGP affect how fast a website loads?

Indirectly. The path BGP selects affects how far data travels and how congested the route is, which can influence speed and reliability.

Why does it matter for AI infrastructure?

AI services often span many regions. BGP lets operators announce services from several locations and shift traffic away from a troubled site, making it an essential tool for keeping those services reachable.

Latest stories

View all

Networking

The Control Plane Can Be a Shared Dependency Across Separate Systems

Two independent-looking systems can still rely on one service to decide what they should do. Configuration management, identity, name resolution and orchestration can become common dependencies even when the data paths are physically separate.

Published

on

Bundles of blue network cables

Photo: Scott Rodgerson / Unsplash

Two independent-looking systems can still rely on one service to decide what they should do. Configuration management, identity, name resolution and orchestration can become common dependencies even when the data paths are physically separate.

The operating distinction

The data plane moves the work, while control functions establish or manage its behavior. Some equipment continues operating through a temporary control interruption; other actions may fail until control returns. The distinction matters because successful ongoing traffic does not necessarily prove that new sessions or changes will work.

Advertisement

Management dependencies can extend beyond the network team. Identity services and access systems may be owned by another group, while the people restoring equipment assume those services are available. That creates an organizational boundary as well as a technical one.

A practical example

Picture a hypothetical network that keeps existing connections running while its management service is unavailable. Monitoring may report that traffic is flowing, yet a new deployment cannot receive the configuration it needs. Both observations can be true at the same time.

Questions worth asking

Duplicated data links do not explain the availability of the services that configure them. Identifying control dependencies helps distinguish uninterrupted traffic from the broader ability to manage, replace and restart equipment after a fault.

  • Which functions keep working when the shared control service is unavailable?
  • Can new sessions and replacement devices be brought into service?
  • How is access to the management system restored during a broader incident?

What the evidence supports

A shared control service is not automatically an unacceptable design. Centralization can simplify management. The task is to identify what depends on it, how interruption affects different operations and how restoration is tested. A diagram should show management dependencies as well as the visible cables.

A useful tabletop discussion asks what can be observed, changed and recovered if the common management service is absent. The answer should distinguish a service that can continue automatically from one that needs human intervention or new configuration. It can then identify the approved route for that intervention. This provides a better picture of recovery capability than a diagram that shows duplicated data links but omits who or what controls them.

Advertisement

Separate the ability to keep current work moving from the ability to manage or restart it.

Quick check

How much did you catch? Tap a question to see the answer.

1. How can separate systems share a dependency?

Answer: Through control functions like identity, configuration management, name resolution or orchestration.

2. Does flowing traffic prove new changes will work?

Answer: No. Existing connections can run while new sessions or deployments fail.

3. Why is this an organizational issue too?

Answer: Identity and access services may belong to another team.

A Map of Common Control Dependencies

Control dependencies are often invisible on a physical diagram because they do not occupy their own cables. Listing them explicitly is a useful first step. In many environments, the shared services include:

  • Identity and authentication. The systems that confirm who an engineer or automated process is and what they are allowed to change.
  • Name resolution. The services that translate names into addresses for both applications and management tools.
  • Configuration management. The repositories and tools that hold intended device settings and push them out.
  • Orchestration and scheduling. The systems that decide where workloads run and start or stop them.
  • Certificates and secrets. The services that issue and renew the credentials systems use to trust each other.
  • Time synchronization. Accurate time underpins logging, certificate validity and coordination.
  • Out-of-band management. The separate access path engineers use when the main network is unavailable.

Running a Control-Plane Tabletop Exercise

A tabletop exercise lets a team walk through a scenario without touching live systems. A simple structure works well.

  1. Pick one shared service. Assume it is unavailable for a defined period.
  2. List what keeps running. Identify functions expected to continue automatically, such as existing traffic flows.
  3. List what stops. Identify actions that would fail, such as new deployments, logins, configuration pushes or device replacements.
  4. Trace the recovery route. Determine how engineers would reach the affected systems, and whether that route itself depends on the missing service.
  5. Check emergency access. Confirm that break-glass credentials or local access methods exist, are controlled and have been tested.
  6. Record corrections. Capture missing documentation, unclear ownership or circular dependencies discovered during the walk-through.

Common mistakes

A frequent discovery is a circular dependency, where the tool needed to restore a service relies on that same service. Another is an out-of-band network that quietly shares authentication or name resolution with the main environment. A third is assuming that the identity team will be available and informed during an infrastructure incident, when no joint procedure exists. Finally, emergency credentials are sometimes created and never tested, so nobody knows whether they still work.

What This Means for Businesses and Readers

For organizations using cloud and hosted services, control-plane dependencies help explain why an outage can affect services that appear unrelated. A disruption in a shared management or identity function can prevent changes and new connections across many systems while existing work continues. For readers trying to understand an incident report, distinguishing between data-plane and control-plane effects often clarifies what customers actually experienced.

Separate cables can carry the work. Something still has to tell them what to do.

This is general education about system design. It does not assess any particular provider’s architecture.

Questions Readers Ask

Is centralizing control a mistake?

Not necessarily. Centralized management can improve consistency and security. The important part is understanding and testing what depends on it.

What is the difference between the data plane and the control plane?

The data plane carries the actual traffic or work. The control plane decides how that traffic is routed, configured and managed.

Why might existing connections survive while new ones fail?

Established sessions may already have the information they need, while new sessions require lookups, authentication or configuration from the unavailable service.

What is break-glass access?

A tightly controlled emergency method of reaching systems when normal access paths are unavailable, used under defined conditions and recorded.

How often should control dependencies be reviewed?

Whenever a shared service is introduced, replaced or reorganized, and periodically in between, because new dependencies tend to accumulate quietly as tools and teams change over time.

BOSSTOX is coming to iPhone

AI infrastructure explainers and news on iPhone, iPad and Apple Watch.

See BOSSTOX

Continue Reading

Networking

Two Fiber Contracts Can Still Share One Excavation Risk

Buying connections from different suppliers does not establish that the physical routes are independent. Somewhere beyond the facility fence, those services may pass through the same duct, bridge or building entrance, creating a common exposure.

Published

on

Road work on a county road

Photo: Tom Shamberger / Unsplash

Buying connections from different suppliers does not establish that the physical routes are independent. Somewhere beyond the facility fence, those services may pass through the same duct, bridge or building entrance, creating a common exposure.

The operating distinction

Network service is a chain of physical assets and operational arrangements. Separate billing relationships can sit on shared infrastructure. Route diversity therefore asks where the cables actually travel and which crossings, access points and equipment rooms they share. Logical paths alone cannot answer every physical question.

Advertisement

The same reasoning applies to restoration plans. An alternate service that survives one local cable fault may still be affected by a wider event. Naming the scenario avoids an all-or-nothing conversation about whether a network is diverse.

A practical example

Imagine two connections that enter a campus from opposite sides but meet at the same nearby road crossing. A fault at that crossing could affect both services. The separate entrances remain useful, but they do not remove that shared section of the route.

Questions worth asking

Different contracts can provide useful commercial options without proving physical independence. Reading the route evidence separately helps identify the actual benefit of the arrangement and the remaining shared exposure that needs another response.

  • Which physical segments are shared outside the property boundary?
  • When was the route information last confirmed with the providers?
  • What restoration options remain if that common segment is unavailable?

What the evidence supports

Route documentation can be incomplete or subject to confidentiality limits. It can also become stale after changes. The practical goal is to establish the important shared risks and the evidence available, rather than assume that a second contract eliminates every possible network interruption.

A route sketch should distinguish confirmed information from an assumption or a supplier statement awaiting clarification. It can then show the important uncertainty without revealing sensitive route details publicly. The point is to make procurement and operating discussions more precise: which kind of damage is covered, which common dependencies remain and what evidence would justify a stronger claim. That is more useful than assuming that different service names imply different physical journeys.

Advertisement

Diversity is a property of the complete path, not simply the number of names on the invoices.

Quick check

How much did you catch? Tap a question to see the answer.

1. Do two suppliers guarantee independent routes?

Answer: No. They may share a duct, bridge or building entrance.

2. What does route diversity ask?

Answer: Where the cables physically travel and which crossings they share.

3. What could two entrances on opposite sides still share?

Answer: The same nearby road crossing.

How Shared Segments Usually Hide

Common exposure rarely announces itself on a contract. It tends to sit in places that are easy to overlook because they are outside the property and outside the day-to-day attention of the facility team.

  • Shared conduit or duct banks. Different providers may lease space in the same underground structure along a road.
  • Bridge and rail crossings. Physical geography often funnels routes toward a small number of practical crossing points over rivers, highways or rail lines.
  • Common meet points. Carriers can hand traffic off in the same nearby building or cabinet before it reaches the facility.
  • Resold or leased capacity. One supplier may carry traffic over another supplier’s fiber, so two names on two invoices can describe one physical cable.
  • The same building entrance. Even when routes are separate for miles, they may converge on a single entrance room or cable vault.

A Practical Route Review, Step by Step

Facility teams and buyers can approach route diversity as a structured review rather than a yes-or-no question.

  1. Request route information from each provider. Ask for the level of detail they are able to share, recognizing that some route data is confidential.
  2. Mark known convergence points. Identify crossings, meet points, entrances and any segments where the routes appear to run near each other.
  3. Label the quality of each claim. Separate confirmed information from provider statements awaiting verification and from assumptions.
  4. Name the scenarios. Consider a single cable cut near the site, construction damage along a shared road, a bridge closure and a problem in a shared equipment room.
  5. Map restoration options to each scenario. Decide which services would remain available and which would require a separate response.
  6. Set a refresh date. Routes change when providers reroute, rebuild or sell assets. Agree on how often the information will be confirmed again.

Common mistakes

One mistake is accepting a provider’s diversity label without asking what it covers. Another is checking diversity once at contract signing and never again. A third is focusing entirely on the long-haul portion of a route while ignoring the last stretch near the facility, where excavation work is often most likely to occur. A fourth is assuming that a wireless or alternate technology backup has no shared dependency, when it may rely on the same power, building or tower infrastructure.

What This Means for Businesses Relying on Connectivity

For organizations that depend on a data center or cloud region, network diversity is part of the resilience they are buying, whether or not they negotiate it directly. A provider that can explain its known shared exposures clearly is usually giving a more honest picture than one that simply states its routes are diverse. For readers following infrastructure companies, route quality is one of the less visible factors behind service reliability, and it rarely appears in a headline.

The most useful diversity statement describes which failures the arrangement is expected to survive and which it is not.

Questions Readers Ask

Why do providers keep route details confidential?

Detailed route maps can create security concerns and may be commercially sensitive. Buyers can often obtain enough information to assess shared risk under appropriate agreements.

Is physical diversity always worth the cost?

It depends on how much an interruption would cost the business and which scenarios matter most. The decision benefits from naming the risk rather than buying diversity as a general label.

Can two routes ever be fully independent?

Complete independence is difficult to prove. The practical aim is to reduce the most likely and most damaging shared exposures and to know which ones remain.

How does excavation risk relate to fiber?

Buried cable can be damaged during digging for roads, utilities or construction. Shared corridors mean one digging accident can affect more than one service.

BOSSTOX is coming to iPhone

AI infrastructure explainers and news on iPhone, iPad and Apple Watch.

See BOSSTOX

Continue Reading

Networking

InfiniBand vs. Ethernet for AI Clusters

InfiniBand offers a tightly integrated path for synchronized AI traffic, while Ethernet offers broader compatibility and choice; the right fabric depends on workload, scale, software, and operating priorities.

Published

on

A hand plugging in an ethernet cable

The networking choice inside an AI cluster is not a simple bandwidth comparison. Training jobs repeatedly move parameters, gradients, and activations between accelerators. If the network stalls, expensive GPUs wait. The result can be lower utilization even when every link’s headline speed looks impressive.

InfiniBand and Ethernet can both build large clusters. They differ in how much of the transport, congestion control, topology, and software stack is standardized or integrated for the target workload.

Why AI traffic is unusual

AI training produces synchronized bursts. Many accelerators finish a step and communicate at nearly the same time. That creates a traffic pattern that is sensitive to tail latency, congestion, packet loss, and collective-operation performance.

Advertisement

A general enterprise network can tolerate variable paths and occasional retransmission. A large training cluster may lose efficiency if a small number of links become hot and delay an all-reduce operation. The network is part of the compute system, not just plumbing.

InfiniBand’s case

InfiniBand was designed for high-performance computing. It supports low-latency communication, remote direct memory access, and features intended to keep data moving between nodes with limited CPU intervention.

NVIDIA’s April 2025 description of a DGX SuperPOD deployment cited Quantum-2 InfiniBand networking and a digital-twin validation process. The company said a SoftBank deployment of 510 DGX B200 systems was completed in three weeks, compared with a typical six-plus months, and that NVIDIA estimated the avoided downtime at roughly $1 million per day for a 1,000-server, 8,000-GPU data center. That estimate is NVIDIA’s analysis, not an independent industry average, but it illustrates why network deployment speed can have financial value.

InfiniBand’s strength is a validated stack. Hardware, drivers, collective libraries, and topology can be designed together. That can reduce the integration burden for a customer that wants a high-performing training appliance.

Its weaknesses are ecosystem and flexibility. It can require specialized adapters, switches, expertise, and operational tools. A company with a large Ethernet organization may prefer a fabric it already knows.

Advertisement

Ethernet’s case

Ethernet is widely deployed across data centers and connects servers, storage, offices, and the public network. It offers a large supplier base, familiar management tools, and multiple implementation choices.

AI Ethernet systems commonly use lossless or low-loss designs, remote direct memory access over Converged Ethernet, explicit congestion notification, and careful buffer and topology planning. The performance depends heavily on configuration. “Ethernet” by itself does not say whether a cluster will perform well.

Intel’s Gaudi 3 materials emphasize standard Ethernet and a 32-node all-Ethernet reference design. The pitch is not merely lower equipment cost. It is the ability to use existing operational skills and to avoid a completely closed networking path.

Speed changes the economics

Arista announced new 800G platforms in October 2025 and said 800GbE port shipments more than tripled sequentially in the second quarter of 2025, according to cited market research. The company described 3.2-terabit-per-second HyperPorts and AI uses including lossless training and inference.

800G matters because an AI rack can have many high-bandwidth links. If each accelerator needs 800 gigabits per second of east-west bandwidth, a 72-accelerator rack creates enormous switching demand. Moving to 1.6T transceivers can reduce port counts or support larger bisection bandwidth, but it also raises optical, thermal, and signal-integrity requirements.

The comparison should be made at job completion time

A network that delivers higher link speed but poor congestion behavior may lose to a slower network with better collective performance. The useful test is end-to-end: time to train, tokens per second, scaling efficiency from one node to 32 or 128 nodes, tail latency, and behavior during failures.

The test should include the actual model, precision, batch size, topology, and software release. A vendor’s ideal benchmark can be informative, but it is not a deployment guarantee.

Operations may decide the outcome

A cluster can fail financially through poor utilization. If the team cannot troubleshoot the fabric, the expensive accelerators sit idle. A familiar Ethernet operation may be worth more than a theoretical performance advantage. Conversely, a dedicated AI service with a specialized team may benefit from the tighter InfiniBand stack.

A hybrid architecture is common. InfiniBand or specialized Ethernet can carry accelerator-to-accelerator traffic, while ordinary Ethernet handles management, storage, and user access. The boundary must be clear so a failure in one network does not quietly degrade the other.

The decision rule

Choose InfiniBand when predictable scale-out training, validated deployment, and low-latency collectives dominate. Choose Ethernet when supplier choice, operational familiarity, interoperability, and mixed workloads matter more. Measure both on the workload that pays the bills.

The procurement decision should include the people who will operate the fabric. Ask how many engineers are trained on the selected switches, how firmware is qualified, how telemetry is exported, and how a bad optic is isolated. Also ask whether the vendor can support a mixed-generation cluster during a refresh. A network that is technically fast but difficult to diagnose can reduce accelerator utilization for weeks. In that sense, operational simplicity is a performance feature, not an administrative preference.

At very large scale, fabric choice also affects the power budget. More ports, higher-speed optics, and additional switch tiers consume electricity and occupy rack space. That overhead should be included in the same total-cost model as accelerator power. A lower-cost accelerator that needs a larger network may not be cheaper at the cluster level. The fair comparison is the amount of useful work delivered by the complete system after networking, cooling, software, and operations are included.

Sources

  1. NVIDIA, “NVIDIA Helps Build AI Factories Faster Than Ever with DGX SuperPOD,” April 11, 2025: developer.nvidia.com
  2. NVIDIA, “Blackwell: Born for Extreme-Scale AI Inference,” 2025: blogs.nvidia.com
  3. Intel, “Intel Gaudi AI Accelerator Products,” accessed October 2026: intel.com
  4. Arista, “Arista Networks Unveils Next Generation Data and AI Centers,” October 29, 2025: arista.com
  5. NVIDIA, “Reference Architectures: Deep Dive,” accessed October 2026: docs.nvidia.com

BOSSTOX Research articles are drafted with AI assistance and reviewed by our editors before publication. See our editorial standards.

Continue Reading

Trending